• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
SensorsONE

SensorsONE

Measurement Instrumentation Products

  • Products
  • Contact

IWSL Potable Water Submersible Level Sensor

Select Options ⇒ Request Price
PDF

IWSL Potable Water Submersible Level Sensor

IP68 protect pressure sensor for monitoring potable water level to depths of 100 metres.

The materials and fittings used in the mechanical construction of the IWSL water level sensor meet the standards required by the water supply byelaws of England, Wales and Scotland.

Contents

  • Product Parameters
  • Product Description
  • Product Applications
    • Community well reservoir
    • Building water reservoir level
  • Product Help
    • Long cable length
    • Sailboat water tank level with Arduino
  • Related Documents
    • Specification data sheet

Product Parameters

  • Hydrostatic Level Ranges: 0-1 up to 0-100 mH2O gauge, 0-2 up to 0-10 bar absolute
  • Accuracy: 0.1% or 0.06% full scale BSL linearity (11-12 bit resolution)
  • Output Signal: 4-20 mA current loop output, voltage output or mV/V
  • Electrical Connection: IP68 seal and Polyurethane coated cable
  • Pressure Connection: 1/4 BSP male with protective nose cone
  • Media Compatibility: Stainless steel 316L sensor body and diaphragm with EPDM O ring seal and PUR coated cable
  • Diameter: 25 mm (1 inch)

Product Description

The IWSL potable water submersible pressure sensor can be used in many applications throughout the freshwater supply system such as monitoring river levels, surface and underground reservoir depth, water tower height, groundwater borehole depth and aquifer water levels.

The IWSL provides an analogue signal which is proportional to the hydrostatic pressure of the water column above the submerged sensor. To accommodate the standardised signal used in a particular water region there is a choice of outputs from low power consumption millivolt or voltage output for remote isolated installations and OEM product integration to 4-20mA current loop for water process and distribution control systems.

Product Applications

Community well reservoir

Monitor water level in a community water well reservoir which is 8 feet deep, and holds 20,000 gallons.

  • SKU ID: s1-iwsl-0002
  • Pressure Range: 8
  • Units: ftH2O
  • Range Type: Gauge / Vented (atm to +P)
  • Output Signal: 4-20mA (2wire)
  • Non-Linearity and Hysteresis: 0.1% FS
  • Thermal Zero Shift: 0.02% FS per °C
  • Cable Type: PUR
  • Cable Length: 40
  • Cable Length Units: Feet (ft)
  • Housing & Diaphragm Material: Stainless steel 316L
  • Media Exposed Seals: EPDM
  • Process Connection: G1/4 male DIN3852 with removable nose cone

Building water reservoir level

Building domestic water reservoir level measurement for a building automation system, where it is difficult to install an ultrasonic device.

  • SKU ID: s1-iwsl-0001
  • Part No: IWSL-G0600-5A2-AAE-013-000
  • Pressure Range: 20
  • Units: ftH2O
  • Range Type: Gauge / Vented (atm to +P)
  • Output Signal: 4-20mA (2wire)
  • Non-Linearity and Hysteresis: 0.1% FS
  • Thermal Zero Shift: 0.02% FS per °C
  • Cable Type: PUR
  • Cable Length: 40
  • Cable Length Units: Feet (ft)
  • Housing & Diaphragm Material: Stainless steel 316L
  • Media Exposed Seals: EPDM
  • Process Connection: G1/4 male DIN3852 with removable nose cone

Product Help

Long cable length

We require 100 metres of cable, but only 10 metres of the cable will be submerged in fresh (potable) water tanks, so can the IWSL be supplied with that length of cable?

KL1 Cable Junction Box for Submersible Level TransmittersThe submersible cable fitted to the IWSL includes air breather tube for provide an atmospheric pressure reference for automatically correcting the water pressure reading.  This cable is quite expensive for running along the ground, so you may want to consider using a vented junction box where the cable exits the tank, and run a cheaper sensor cable without a breather tube along the ground.

Sailboat water tank level with Arduino

I would like to measure water level in a water tank on a sailboat using an Arduino board. The water level is approx 0-0.6m

We would suggest the 5 volt input, 0.5 to 4.5 volt output option for compatibility with the available sensor power supply and analog inputs of the Arduino electronics.

  • SKU ID: s1-iwsl-0003
  • Part No: IWSL-G0060-9A2-AAE-005-000
  • Pressure Range: 0.6
  • Units: mH2O
  • Range Type: Gauge / Vented (atm to +P)
  • Output Signal: 0.5-4.5Vdc (3 wire)
  • Non-Linearity and Hysteresis: 0.1% FS
  • Thermal Zero Shift: 0.02% FS per °C
  • Cable Type: PUR
  • Cable Length: 5
  • Cable Length Units: Metres (m)
  • Housing & Diaphragm Material: Stainless steel 316L
  • Media Exposed Seals: EPDM
  • Process Connection: G1/4 male DIN3852 with removable nose cone

Related Documents

Specification data sheet

  • IWSL product data sheet

Request Product Price

Please select the options you require for the IWSL Potable Water Submersible Level Sensor in your application and request a quote.

  • Enter max pressure reading for output signal scaling
  • Please enter info about your application and include any other requirements.


Primary Sidebar

Liquid Level Sensor Specifier

Specify a liquid level sensor
Select your liquid level sensor requirements

Product Enquiry

Send us your enquiry for IWSL Potable Water Submersible Level Sensor to get assistance with this product type.

Email Your Enquiry

enquiries@sensorsone.com
By clicking "OK" or continuing to use this website you are providing your consent to use cookies as described in our Privacy Policy

© 2019 SensorsONE Ltd, all rights reserved

  • Home
  • Legal
  • Contact