An absolute pressure sensor for vacuum insulation air extraction use to measure vacuum pressure of air over a range of 0 to 15 psi abs from the G1/4 male process connection, and sending the corresponding mV/V signal through the submersible cable electrical connection.
Pressure Transducers (mV)
Millivolt output pressure transducer product specs & help guides for strain gauge bridge output pressure transducers to measure gauge, absolute and differential pressures with high dynamic response, low power consumption and minimal active electronic components. These types of sensors have low voltage output signals which are proportional to the input supply voltage and typically have a 20 mV, 30 mV, 33 mV or 100 mV when supplied by 10Vdc.
This pressure transducer millivolt output calculator provides a way to determine the output reading and range from the applied pressure, pressure transducer range and strain gauge output characteristics.
Economical corrosion resistant ceramic diaphragm pressure sensor for educational measurement instrumentation measuring over a 0-1 bar absolute pressure range and generating a strain gauge millivolt output signal.
A strain gauge output pressure sensor for food processing use to measure pressure of air over a range of 0 to 100 psi g from the 1/4 NPT male process connection, and sending the corresponding mV/V signal through the DIN plug electrical connection.
A millivolt output pressure sensor for food processing use to measure pressure of air over a range of 0 to 100 psi g from the 1/4 NPT male process connection, and sending the corresponding mV/V signal through the DIN plug electrical connection.
Economical corrosion resistant ceramic diaphragm pressure sensor for measuring over a 0 to 400 bar gauge pressure range and generating a 2 millivolt per volt output signal.
Economical corrosion resistant ceramic diaphragm pressure sensor for measuring over a 600 bar gauge pressure range and generating a 2 millivolt per volt output signal.
Economical corrosion resistant ceramic diaphragm pressure sensor for measuring over a 0 to 600 mmHg gauge pressure range and generating a 2 millivolt per volt output signal.
Pressure sensor elements with sensing diaphragms made from alumina ceramic (Al2O3) for electronic & mechanical oem integration into measurement & control instrumentation designs.
This pressure transducer will measure hydraulic pressure generated by a compression machine and produce a 3mV/V output sensitivity.
This guide will help you select a millivolt output pressure transducer and explain the advantages of using this type of pressure sensor.
I am looking to measure pressure in a water network with a range of 0-10bar, overpressure of 40 bar & 20m long IP68 protected cable for flood protection.
Differential pressure sensor product selection guide for sensors used to measure the difference in pressure between two points.
Before purchasing a pressure sensor, there are a number of application questions you will need to answer to ensure it is fit for purpose
The IMP pressure transducer without any amplification electronics will provide a response time of around 23 microseconds (0.023 msec) for a 2 bar range.
The stripped down OEM version of the IMP transducer is specifically designed for use inside freshwater pressure loggers
Versatile low price pressure sensor with a wide selection of electrical and mechanical options for customisation.
4 wire describes a sensor which has a either a wheatstone bridge strain gauge configuration or a amplified output sensor where the supply input is isolated from the signal output. 4 wire is also used to describe a resistive thermometer that is wired so that the error caused by the connecting wire on each side […]
A pressure transducer is a device which converts an applied pressure into a measurable electrical signal.
An Isolation diaphragm is a thin membrane which is used to isolate the media on one side of a diaphragm from media on the other side.
Low voltage output submersible pressure transducer for connecting to a data logger to measure water levels up to 6 metres deep in a river.
Four wire strain gauge type pressure transducer with a twenty millivolt full scale output with a steady 10 volt supply input.
What is the method of shunt calibration in relation to an indicator connected to a pressure transducer?
There are many materials used for constructing pressure sensors, but those made from stainless steel are considered the most reliable and durable.
When browsing through pressure measurement products you will notice that some are called pressure transducers and others are called pressure transmitters.
Miniature size 1/2 inch diameter stainless steel pressure sensor with an amplified 0.5 to 4.5 Vdc output. Pressure ranges start from 10 up to 400 bar.
Passive compensated pressure transducer with a four arm semiconductor Wheatstone bridge circuit which produces a 100 millivolt with a 10 volt excitation.
Ceramic strain gauge pressure transducer with a 2mV/V or 10mV/V output signal in pressure ranges from 1 bar up to 700 bar gauge or absolute.
Motorsport pressure transducer with 21mm diameter and and 24mm body length for pressure ranges from 0.5 up to 600 bar gauge or absolute. Available with millivolt and amplified voltage output signals.
Very high range pressure sensor with a millivolt output signal for pressure ranges from 1000 up to 5000 bar gauge.
Flush diaphragm piezo-resistive pressure sensor for food processing and plastic injection moulding applications with a millivolt output signal in pressure ranges from 10 up to 1000 barg.
Strain gauge pressure sensor with a millivolt output direct from a four arm wheatstone bridge strain gauge circuit in pressure ranges from 10 up to 1000 bar gauge.
Understand what parameters are included in pressure sensor accuracy specifications and what techniques were used, so that a true comparison can be made.
For the best frequency response use a strain gauge pressure transducer that provides a mV output without any amplification.