measure the level and temperature of potable water in an underground water storage tank with a 10 ft diameter and a horizontal orientation.
ATEX rated submersible pressure sensor for fleet management system (FMS) petrol applications .
Low powered submersible level sensor with a 25 metre depth range, for use with a arduino controller to manage borehole drawdown and protect pump.
A drinking water approved submersible level sensor for submerging in a filtered rainwater cistern and measuring the depth over a range of 0 to 13ft from the nose cone, and sending the corresponding 4-20mA signal through the submersible cable electrical connection.
A submersible water temperature and level measurement transmitter for submerging in a borehole and measuring temperature over -5 to +50C, and depth down to 10m, from the nose cone, and sending each measurement with a separate 4-20mA signal through the submersible cable electrical connection.
A submersible water level sensor for submerging in a drinking water reservoir and measuring the depth over a range of 0 to 5ft from the nose cone, and sending the corresponding 4-20mA signal through the submersible cable electrical connection.
A submersible liquid level sensor for submerging in a dust suppression system freshwater tank and measuring the depth over a range of 0 to 3m from the flush diaphragm, and sending the corresponding 4-20mA signal through the submersible cable electrical connection.
A high resolution submersible water level sensor for submerging in a freshwater tank and measuring the depth over a range of 0 to 10m from the flush diaphragm, and sending the corresponding 4-20mA signal through the submersible cable electrical connection.
I am hoping to use a borehole where the pump is about 25m below the surface. I would like the pump to operate automatically by switching on when the water has returned to about 14m below ground level and off at about 20m below the ground.
Cylindrical pressure sensor probe for lowering into a well to measure the depth of water down to 350 feet.
Submersible water level sensor for monitoring the depth of water in a retention basin down to 20 feet.
Submersible hydrostatic level transmitter with a range of 0 – 25 metres for installing outdoors and a digital indicator for installing indoors.
Measure the level of Adblue® diesel exhaust fluid as part of a tank monitoring system used to support depots operating a fleet of diesel trucks.
We need to measure the water level in a well down to 200 meters to protect a well pump by ensuring that it always stays under water
The CNS is obsolete and no longer manufactured. As an alternative for your fuel oil application we would suggest a 1.6 metre range LMP307
Rangeable submersible depth transmitter with a digital interface for re-ranging to any depth down to 10 m max.
We are trying to measure pressure in a gas tank filled with stoddard solvent.
Water level indicator for a 2 metre deep rain water storage tank located underground.
Submersible diesel level pressure sensor for installing in the bottom of tanks up to 2 metres deep.
One inch diameter bore hole water level measurement transducer for measuring water depth up to 100 metres.
Fresh water level sensor for submersing in rivers with a hydrostatic pressure range for measuring water depth up to 2 metres.
Combined digital pressure gauge and submersible level sensor for measuring the quantity of diesel or oil present inside industrial storage tanks up to 10 meters high.
Voltage output fresh water submersible pressure sensor for measuring borehole well depth from 0 to 150 metres of water column.
Is there anything portable that could be dropped into different sized and irregularly shaped tanks to measure the amount of change in liquid height?
We are looking for a level sensor for submerging into a water tank to measure a level between 10 and 300 cm.
Submersible level transmitter for measuring liquid level with a 4-20mA current loop or a 0-10V voltage output plus optional ATEX approval for intrinsically safe use in hazardous areas in ranges from 1mH2O up to 250mH2O. The LMP307 is suitable for use on potable water with no leaching, and can be supplied with a drinking water certificate according to DVGW and KTW.
Do you have a battery operated solution to measure the level of a Water pond?