Compound range intrinsically safe and SIL 2 approved pressure sensor for controlling the inert gas pressure in tanks containing flammable cargo.
A fuel tank mounted level sensor for measuring the height of diesel in a automatic diesel fire pump engine fuel tank over a range of 0 to 48in from the 1/4 BSP male process connection, and sending the corresponding 0-10Vdc signal through the weather proof cable electrical connection.
A data acquisition compatible level sensor for submerging in a lake stilling well and measuring the depth over a range of 0 to 3ft from the nose cone, and sending the corresponding reading via an SDI-12 serial interface through the submersible cable electrical connection.
Low range pressure sensors for monitoring inlet and outlet pressure of a natural gas booster pump used to raise the pressure feeding into a demand regulator which provides fixed supply pressure to fuel the back-up power generator.
A plastic submersible liquid level sensor for submerging in a chemical tank used for injecting minerals into water lines on farms, and measuring the depth over a range of 0 to 120 cm from the nose cone, and sending the corresponding 4-20mA signal through the submersible cable electrical connection.
Low range intrinsically safe digital display pressure gauge for pipe mounted use in natural gas measurement applications on feeds to industrial gas boiler, capable of measuring 0 to 40 inH2O g pressure with 0.25% accuracy and connected using a 1/4 NPT male fitting. Also includes USB and peak & valley reading hold.
A low range pressure sensor for farming use to measure freshwater tank fluid level over a range of 0 to 1.5 psi g from the 1/4 NPT male process connection, and sending the corresponding 4-20mA signal through the weatherproof cable electrical connection.
An intrinsically safe, marine approved compound range pressure transmitter for ship cargo tank IG system use to measure pressure of inert gas over a range of -10 to 30 kPa g from the G1/2 male process connection, and sending the corresponding 4-20mA signal through the DIN plug electrical connection.
Low range digital display pressure gauge for portable use in air measurement applications, capable of measuring 0 to 100 mbar g pressure with 0.25% accuracy and connected using a G1/4 male fitting. Also includes USB, logger and cal cert.
A pressure sensor with internal amplifier for aerospace research test rig use to measure pressure of air over a range of 0 to 100 mbar differential from two 6mm flexible tubing connections, and sending the corresponding 0-5Vdc signal through the DIN plug electrical connection.
A gauge pressure sensor for water treatment use to measure pressure of freshwater over a range of 0 to 10 kPa g from the G1/4 male process connection, and sending the corresponding 0-5Vdc signal through the submersible electrical connection.
Economical stainless steel diaphragm pressure sensor with semiconductor strain gauges for measuring over a 0 to 100 mbar gauge pressure range and generating a 0 to 5 volts output signal.
A hydro-static pressure transmitter for storage tank level monitoring use to measure level of 36% hydrochloric acid over a range of 0 to 1 mH2O g by immersion in the tank, and sending the corresponding 4-20mA signal through the submersible electrical connection.
I have a 300 gallon enclosed 4 feet high round tank which is filled with sodium hypochlorite (bleach). I need a non-metallic level sensor that will output a 4-20ma signal. I can’t have any metal in contact with the bleach.
This low power consumption SDI-12 interface sensor will measure the water level of roadside creeks and streams to sense the level of flooding.
Low cost stainless steel 316L submersible liquid level sensor with silicon strain gauge technology for measuring over a 0 to 100 mbar gauge hydrostatic pressure range and sending out a 0 to 5 volts signal.
Stainless steel based compact pressure transmitter for measuring pressure of incoming boiler room natural gas supply up to 100 mbar gauge.
0…1 mH2O or 0…3 ftH2O liquid level range, 4…20 mA, 0…10 V, or 0…5 V output signal hydrostatic liquid level sensors.
0…100 mbar or 0…1.5 psi pressure range, 0…10 V, 0…5 V, or 1…5 V output signal pressure sensors.
Pressure sensor for measuring the differential pressure generated by water flowing through an orifice plate in a pipe, and converting the output to a water flow measurement.
0…100 mbar, 0…1.5 psi, 0…40 inH2O, or 0…10 kPa pressure range, 4…20 mA output signal pressure sensors.
Measure the air intake filter pressure difference on an industrial air compressor with this -100 to +100 mb range, 0 to 10 volt output differential pressure sensor.
Monitor the suction pressure at the top of a biogas vertical extraction well in a landfill site.
The DMP331 is a pressure transmitter which is both ATEX and IECEx intrinsically safe approved for use in zone 20 potentially explosive dust environments.
The XMD differential pressure transmitter has an accuracy of 0.1% FSO for turn-down ≤ 5:1, and an overpressure on either side of up to 130 bar.
Record gas pressures to determine variation in supply to your rooftop make-up air units.
Depth probe for monitoring the level of raw leachate in feed tanks up to 1 metre high on a landfill site.
I have a tank 1 metre cubed that holds 1000 Litres of diesel for a generator. I am trying to find a sensor that will inform me of the contents/level
We are looking for an immersion gauge sensors with vented cable for measuring the level of oil.
Level sensor for sitting in a sea water tank on a ship deck to measure depth variation between 0-30cm.
DMP320 which has a high sampling rate of 10 kHz so you will easily resolve the dynamic change characteristic over 0 to -200 psf within the 8sec window.
I have an Argon filled chamber that I wish to measure pressure up to 100 millibar relative to atmosphere.
ATEX and IECEX certified pressure transmitter for gas or dust and has all stainless steel 316L for use with liquids, and a low pressure range capability.
The DMK351 is a low range intrinsically safe certified pressure transmitter with a ceramic diaphragm that provides high chemical corrosion.
Low range pressure transmitter with a G1/4 female thread for measuring over 0 to 100 millibar relative to atmospheric pressure.
What to use for measuring vacuum pressure on a fuel tank in a hazardous area which is prone to flooding?
Submersible flush diaphragm raw sewage level transmitter for measuring levels of wastewater up to 1 metre in depth.
Atex certified digital manometer with a pressure range of -100 to +100 mbar gauge with data recording, software and a data port to connect to a PC.
4-20 mA signal vacuum transmitter with a 0 to 100 mbara range which can withstand a 5 bar absolute overpressure.
Current output wet/wet differential pressure transmitter with 4-20 milliamp signal for measuring dp between 0 and 1.5 psi on a static line pressure of up to 1885 psi.
Sensor and panel indicator to monitor a pressure drop through a casting of up to 10 kilopascals.
Titanium hydrostatic depth transducer for measuring up to 1 metre depth of sea water.
Screw-in liquid level sensor for measuring the height of biodiesel with 3% sulfuric acid (H2SO4) from 0 to 1 metre head
Food compatible liquid level electronic switch and LED gauge indicator for providing an on/off output at any level threshold from 0 and 1 metre high.
Intrinsically safe atex approved vacuum pressure sensing device with a 4-20 milliamp output for mounting in a vacuum header line for carrying waste print toner ink dust.
Low range pressure transmitter for OEM equipment manufacturers. This IMP LR sensor has a 0 to 40 inH2O gauge for use on liquids or gases.
Differential pressure sensor and local indicator for measuring dp of fluids over the range of 0 to 100 mbar diff
Digital vacuum gauge with digital display for measuring suction pressure down to minus 100 millibar below atmospheric pressure.
2 wire 4-20mA loop transmitter for measuring the level of high temperature water up to 1 meter (3.3 feet).
What submersible pressure sensor should I purchase for measuring a hydrostatic pressure of fresh water up to 1 metre?
Hygienic ATEX approved pressure transmitter for zone 2 to read pressures from 15 to 25mbar.
I’m looking to monitor the depth of water in a river up to around 1 metre deep, but occasionally there is a storm and the river swells to a depth of 10 metres.
What sensor would you suggest for measuring low levels of seawater with a 0-5Vdc?
We are looking for a pressure transmitter with a range from 0 to 100 mbar and a 4-20mA output with a 3 wire electrical connection