DP transmitter for measuring pressure difference between two pressure points which can tolerate up a very high overload pressure independently on either the positive or negative side port or both together at the same time.
Featured Measurement Products
A selection of measurement products widely used in many applications and offering the best features & functions compared to other similar products.
The XSYS-0011 is supplied as a portable transport case with a CMC Multicon colour touchscreen data logger plus an optional MLP-149 portable printer integrated .
Convert a 0 to 20 millivolts range measurement input signal into a 0 to 10 volts output signal.
Convert a 0 to 50 volt range measurement input signal into a 0 to 10 volts output signal.
Convert a 0 to 1 volt range measurement input signal into a 0 to 10 volts output signal.
Low range digital interface submersible liquid level probe with RS 485 Modbus RTU protocol serial bus communications for measuring level of fuel, oil and wastewater in low fill height open tanks.
Measure temperature over a 32 to 122 degrees Fahrenheit range and convert it to a 4 to 20 milliamps loop output signal.
Submersible 4-20mA output sensing probe for immersion in freshwater, seawater or any other compatible liquid to measure liquid temperature.
Convert a 0 to 100 millivolts range measurement input signal into a 4 to 20 milliamps loop output signal.
Convert a 4 to 20 milliamps range measurement input signal into a 0.5 to 4.5 volts output signal.
Convert a 0.5 to 4.5 volts range measurement input signal into a 4 to 20 milliamps loop output signal.
Invert a 4 to 20 milliamp current range measurement input signal into a 20 to 4 milliamp current output signal.
Invert a 0 to 10 volts range measurement input signal into a 10 to 0 volts output signal.
Submersible stainless steel pressure transmitter ideal for geotechnical surveying with a 19mm diameter for measuring hydrostatic water level in bore-holes.
Convert a -10 to +10 volts range measurement input signal into a 4 to 20 milliamps loop output signal.
Add-on temperature cooling accessory for isolating temperature sensitive measurement instrumentation with a ¼ inch BSP male thread from temperatures up to 200 degrees Celsius.
Digital submersible stainless steel liquid level sensor with a Modbus RTU protocol RS 485 serial bus interface.
Convert a 0 to 50 volts range measurement input signal into a 4 to 20 milliamps loop output signal.
Diesel fuel oil storage tank device for measuring liquid level and converting it to an electrical signal to send to other instrumentation protected from diesel ingress when completely immersed in the fuel oil.
Diesel fuel oil storage tank device for measuring diesel fuel level and converting it to an electrical signal to send to other instrumentation.
I am looking for a voltage to current converter that can convert a +/-10V dc input to a 4-20mA output, where a 0 V dc input would result in a 12mA output.
8 channel analogue signal to digital interface module for converting voltage or current signal inputs to a single RS-485 communication interface using Modbus RTU transmission protocol.
Devices protected from liquid ingress when completely immersed in a fluid for measuring liquid level and converting it to an electrical signal to send to other instrumentation.
High speed measurement reading response pressure sensing devices.
Low range pressure measurement sensing devices.
Universal Serial Bus (USB) interface computer connection pressure sensing devices
Low cost OEM diesel fuel or water level sensor for installing inside or outside a storage tank.
USB ready digital pressure sensor for recording pressures with a high speed sample rate of up to 1 kHz to a computer. The UPS-HSR is supplied with a 2m long USB cable, PC software and case. Choose a pressure range from 2.5 bar up to 5000 bar with a G1/4 or 1/4 NPT male up to 1500 bar, and AE F-250-C female up to 5000 bar.
A high range pressure sensor for hydraulic pump use use to measure pressure of synthetic hydraulic oil over a range of 0 to 1,000 bar g from the G1/2 male process connection, and sending the corresponding 4-20mA signal through the DIN plug electrical connection to a microprocessor.
An all welded stainless steel pressure sensor for refrigeration condenser fan and pump control use to measure pressure of anhydrous ammonia (NH3) over a range of 0 to 500 psi g from the 1/4 NPT male process connection, and sending the corresponding 4-20mA signal through the DIN plug electrical connection.
An all welded high range pressure transducer for hydraulic control use to measure pressure of synthetic hydraulic oil over a range of 0 to 300 bar g from the G1/4 male process connection, and sending the corresponding 4-20mA signal through the M12 connector electrical connection.
The PrimAtü 10 low cost low range differential air pressure transducer can detect and display both positive and negative differential pressure variations of very low low pressure ranges from 0.5 up to 1000 mbar/hPa, and output the pressure as a 4-20mA, 0-20mA or a 0-10Vdc analog output.
The DPC low range pressure controller calibrator measures and generates low range pressures over 1, 10, 100 or 1000 mbar, and can be used as a pressure measurement device or as a test and calibration device for pressure sensors and pressure switches.
The Gefran KX pressure sensor is ATEX Ex nA non-sparking approved for use in zone 2 hazardous areas with flammable gas or dust atmospheres, and is SIL 2 approved for additional safety. The KX is available in ranges from -1 to 1 bar up to 1000 bar.
I am hoping to use a borehole where the pump is about 25m below the surface. I would like the pump to operate automatically by switching on when the water has returned to about 14m below ground level and off at about 20m below the ground.
All titanium underwater sensor for measuring seawater depth with a measurement range of 0 to 50 metres providing a 4 to 20 mA output signal.
Hygienic liquid level sensor for mounting to the side of a beverage tank used to store beer, wine, spirits or cider.
0…200 bar or 0…3000 psi pressure range, 0…10 V, 0…5 V, or 1…5 V output signal pressure sensors.
Modbus RTU communications protocol RS485 serial interface, small diameter for water borehole immersion, hydrostatic pressure level sensor.
0…10 bar or 0…150 psi pressure range, 0…10 V, 0…5 V, or 1…5 V output signal pressure sensors.
Pressure sensor elements with sensing diaphragms made from alumina ceramic (Al2O3) for electronic & mechanical oem integration into measurement & control instrumentation designs.
Pressure data logger that can be used in a city municipal water supply system to monitor pressure changes when fire hydrants are flushed
Liquid level transmitters with a 4 to 20 milliamp current loop output signal for determining liquid depth or the fluid level by measuring the hydrostatic pressure.
High range pressure sensors with a measurement range from 0 to 700 bar, 10,000 psi, or 70 MPa.
High range pressure gauges with a measurement range from 0 to 1000 bar or 15,000 psi.
High range pressure sensors with a measurement range from 0 to 1000 bar, 15,000 psi, or 100 MPa.
The TPFAS pressure sensor has a small size flush diaphragm which allows the use of a smaller size G1/4 (1/4 BSP) or M10 x 1 male thread for fitting where there is limited room or access to the process measurement point.
Voltage signal out pressure transducers protected to IP 68 ingress protection rating for immersing in water or other compatible liquids.
These voltage output transducers will provide a linear signal of a few volts that is directly proportional to a specified vacuum range.
Pressure gauges for measuring high temperature fluids or gases. These high temperature pressure gauges are have or include optional extra design features to protect the pressure gauge from high temperature media.
Pressure gauges for capturing measurements and storing them on internal memory. In addition to logging pressure measurements, these data-logging pressure gauges will also display actual pressure readings like any other dedicated digital pressure gauge.
Vacuum range gauges for measuring absolute vacuum or suction pressures which can be permanently installed or used as a test gauge.
Pressure sensors for installing underwater which are constructed to prevent water entering sensitive components and causing damage to the sensor.
Connect a pressure gauge to a desktop or laptop computer via USB or RS232 serial bus connection.
Voltage output pressure transducers for measuring air pressure within air heating and cooling systems, air extraction and filtration and factory pneumatic air systems.
Analog output signal pressure gauges for local indication of pressure and for providing a analog signal input for a PLC or other process control instrumentation.
Pressure transmitters & transducers that are resistant to chemical corrosion for measuring the hydrostatic level of storage tanks or process pressures.
Digital pressure sensors for connecting to a desktop or laptop computer and logging air and liquid pressures at preset intervals.
4 to 20 mA current loop output water level transmitters with a for use with process instrumentation for measuring the level of water in a water well, water reservoir, river or water storage tank.
Pressure gauges for testing and monitoring low range air or liquid pressures. Choose a pressure gauge for displaying low pressure measurement readings in different pressure units such as mbar, hPa, kPa, psi and inH2O.
4-20mA current output sensors for monitoring the pressure of natural gas. Measure very low inlet and output pressure or very high natural gas bottle pressures.
Amplified voltage output transducers for use in applications for measuring pressure of high temperature steam such as sterilizing autoclaves, food processing and power generation.
Vacuum data loggers for recording negative suction pressure or absolute pressure below atmospheric pressure. Log and store vacuum measurements for printing test reports or analysing process trends.
Waste water Level sensors with open face flush diaphragms for measuring the hydrostatic pressure of sewage and effluent waste. Select a level sensor for mounting inside or external to a tank or sewer pipe.
External mounted level sensors for installing on the outside of a liquid storage tank to measure level of tank contents.
Waterproof absolute pressure sensors with absolute reference ranges for monitoring underwater pipe pressures or water depth/level in applications where it is not possible or less practical to provide a vented reference for atmospheric pressure compensation.
Pressure data loggers which combine a battery, logger & pressure sensor all in one standalone instrument.
0 to 5 volts output pressure transducers with amplified signal conditioning electronics and 3 or 4 wire configuration for generating a 0-5Vdc analog signal which corresponds to a specified pressure range.
0 to 20 milliamp output pressure transmitters with a 3-wire configuration for installations where the positive voltage supply is separated from the current loop signal wires.
SIL 2 approved pressure transmitters which have the option for SIL 2 (Safety Integrity Level) certified electronics.
Choose vacuum pressure transmitters for measurements over the low vacuum range of 25 to 760 Torr, using a absolute or negative gauge reference vacuum range.
Hydrostatic pressure sensing devices for measuring liquid level and converting it to an electrical signal to send to other instrumentation.
High temperature pressure transmitters with a 4-20mA output, tolerant to high temperature applications such as steam, food processing & engine monitoring.
Differential pressure transmitters for measuring the DP of fluids and gases across particle filters and along a length of pipe to monitor flow.
ATEX approved pressure transmitters for use in hazardous zones with flammable gases.
Convert a 0 to 10 volts range measurement input signal into a 4 to 20 milliamps loop output signal.
Convert a 0 to 5 volts range measurement input signal into a 0 to 10 volts output signal.
Convert a 0 to 5 volts range measurement input signal into a 4 to 20 milliamps loop output signal.
Convert a 0 to 20 milliamps range measurement input signal into a 4 to 20 milliamps output signal.
Convert a 4 to 20 milliamps range measurement input signal into a 0 to 5 volts output signal.
Convert a 4 to 20 milliamps range measurement input signal into 0 to 10 volts output signal.
Convert a 4 to 20 milliamps range measurement input signal into 0 to 20 milliamps output signal.
The STRAIN universal strain gauge bridge input transmitter can connect any strain gauge loadcell or pressure transducer & provide a mA or volts output
The ISOCON Isolating Signal Converter can accept inputs including 20mA, TC, RTD & voltage signals. The units produce an isolated high level DC output of voltage or current.
We need to measure the water level in a well down to 200 meters to protect a well pump by ensuring that it always stays under water
The DCT 531 digital pressure sensor has a Modbus RTU RS485 interface for transmitting pressure readings over a digital sensor network.
ATEX pressure transmitter to measure the pressure of methane gas line in an anaerobic digestion plant.
LEO Record combined digital manometer & pressure data logging instrument for recording pressures & temperatures that can store up to 57,000 readings.
High precision digital pressure gauge with an accuracy of 0.05% full scale in pressure ranges from 0…30 mbar up to 0…1000 bar.
LEO 2 battery powered digital manometer with pressure ranges from -1 to 3 bar up to 700 bar with an accuracy of 0.1% full scale with 6 pressure units, zero tare & peak hold display functions and optional ATEX approval for intrinsic safety.
Low cost solution to measuring the water level in a borewell with a water height of as much as 100 metres above the submerged sensor
High frequency response pressure sensor with a better than 0.5 millisecond response time and internal digital signal conditioning that samples readings at a rate of 10 kilohertz.
Rugged and easily cleanable pressure/level sensor for use with waste water sewage or sludge.
Combined pressure transmitter and indicator in one package with the option for use with high temperature media such as steam at 200°C
LEX1 high accuracy digital pressure gauge with a +/-300 mbar gauge pressure range for measuring low gas/liquid pressures and vacuums to a high accuracy
Pressure gauge for measuring SF6 gas pressure over the range 0 to 10 bar with the readings compensated for density changes at 20°C
Water pressure transmitter with IP68, 0-10 bar pressure range, 4-20mA output for connecting to water pipes.
Since force is determined from the pressure and the area of the ram piston, you will need a pressure gauge which enables you to configure a custom pressure unit.
The 35X HTC high temperature digital pressure sensor is suited for media temperatures up to 300 °C
Cost effective level sensor 0 – 2m, media is diesel fuel, output is 0-10V